FastClamp

C00-Sleeve Joint Part No. Select Quantity

The Sleeve Joint is designed to provide an in-line joint between two tubes of the same diameter.

C00G20
C00G25
C00G32
C00G40
C00G50
C01-Expanding Connector Part No. Select Quantity

The expanding Connector is designed to provide an in line joint between tubes of the same diameter, and a wall thickness of 3.2mm. It fits flush with the tube surface and can be located inside other fittings. It must not be used as a load-bearing joint, for such applications use a FastClamp type C00.

C01G25
C01G32
C01G40
C02-Elbow Part No. Select Quantity

The 90° Elbow is designed to provide a joint between two tubes at right angles to each other. Often used for railing ends and corners.

C02G20
C02G25
C02G32
C02G40
C02G50
C03-Short Tee Part No. Select Quantity

The Short Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. If tubes need to be joined inside the fitting then a C04G type should be used.

C03G20
C03G25
C03G32
C03G40
C03G50
C04-Long Tee Part No. Select Quantity

The Long Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. It allows the through tube to be joined inside the fitting. An alternative is the C03G type fitting.

C04G20
C04G25
C04G32
C04G40
C04G50
C05-Variable Elbow Part No. Select Quantity

The Variable Elbow is designed to make joints at an angle of between 15° and 60°.

C05G25
C05G32
C05G40
C06-Internal T Joint Part No. Select Quantity

The Internal T joint is designed to provide an angled joint between a tube and a FastClamp fitting when used in conjunction with C02G and C03G type fittings. Often used for railing tops and midrails to accommodate a slope as offset railing.

C06G25
C06G32
C06G40
C07-45° Tee Part No. Select Quantity

The 45° Tee is used as a bracing and strut component for strengthening structures.

C07G25
C07G32
C07G40
C10-Swivel Base Plate Part No. Select Quantity

The Swivel Base is designed to provide a base fixing. It is usually used in conjunction with a C36G type fitting to make a C46G type base swivel combination. This fitting does not provide sufficient rigidity to be used as a railing base without other means of support.

C10G
C11-Base Flange Part No. Select Quantity

The Wall Flange is designed to provide a positional wall or base fixing. It is not recommended to use this fitting as a structural railing base.

C11G20
C11G25
C11G32
C11G40
C11G50
C12-Railing Base Flange Part No. Select Quantity

The Railing Base is designed to provide a base for railings and other structures. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C12G25
C12G32
C12G40
C13-Railing Vert Side Supp Part No. Select Quantity

The Railing Vertical Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C13G25
C13G32
C13G40
C14-Railing Side Supp. Horiz Cast Fitting Part No. Select Quantity

The Railing Horizontal Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C14G25
C14G32
C14G40
C15-Side Palm Fitting Part No. Select Quantity

The Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C15G25
C15G32
C15G40
C16-Handrail Bracket Part No. Select Quantity

The Handrail Bracket is designed to secure handrail tube to a wall. It can also be used on top of walls as a fixing for a low rail.

C16G20
C16G25
C16G32
C16G40
C17-Ground Socket Part No. Select Quantity

The Ground Socket is designed to provide a base that can be cast into the ground to support a post. The post is removable. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C17G25
C17G32
C17G40
C18-Base Flange with Integrated Toeboard Part No. Select Quantity

The Base Flange with Integrated Toeboard is ideal for guardrailing and balustrading applications where the addition of a toeboard is required. The side plates have slotted holes to allow for a degree of sideways movement for ease of installation. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions.

C18G40
C20-3 Way 90° Elbow Part No. Select Quantity

The 3 way 90° Elbow is designed to provide a neat corner for the upper rail of guardrail or frames.

C20G20
C20G25
C20G32
C20G40
C20G50
C21-Corner C/W Throu Tube Part No. Select Quantity

The Corner Complete with through tube is designed to provide a 90° corner for the intermediate rail of guardrail or frames.

C21G20
C21G25
C21G32
C21G40
C21G50
C22-Two Socket Cross Part No. Select Quantity

The Two Socket Cross fitting provides the midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting.

C22G20
C22G25
C22G32
C22G40
C22G50
C23-Side Outlet Tee Part No. Select Quantity

The Side Outlet Tee fitting provides a three way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting.

C23G20
C23G25
C23G32
C23G40
C23G50
C24-4 Way Cross with Centre Tube Part No. Select Quantity

The 4 Way Cross fitting provides a four way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting. This fitting may also be used for the top rail with the centre post capped with a C65 Plastic Stop End.

C24G20
C24G25
C24G32
C24G40
C24G50
C25-Short Tee Swivel Part No. Select Quantity

Short Tee Swivel fittings are normally used in pairs to facilitate corner angles of 90° to 180°. It is also used on staircases with a C02 and C03 fittings in conjunction with a short piece of tube and a C65 Plastic End Cap in landing areas. When ordering please specify the number of fittings required, not the number of pairs.

C25G25
C25G32
C25G40
C28-Socket Cross Adjustable 30°-45° Part No. Select Quantity

The Adjustable 2 Socket Cross fitting will accommodate any rake angle from 30° to 45°. This fitting is not recommended as the top fitting on a guardrail or balustrade system, use the C29 Adjustable Short Tee.

C28G25
C28G32
C28G40
C29-Adjustable Short Tee Part No. Select Quantity

The Adjustable Short Tee fitting will accommodate any rake angle from 30° to 60°. This fitting is commonly used for the top rail of handrail to accommodate the rake angle on slopes. It can also be used for any Tee Joint to make at an angle of between 30° and 60° for light weight structures.

C29G25
C29G32
C29G40
C30-Colla Part No. Select Quantity

The Collar fitting can be used to support the C03 fitting when the latter is used as a hinge. It can also be used to increase the load capacity of another fitting when used together. The C30 can be used as a stop for a sliding tube.

C30G20
C30G25
C30G32
C30G40
C31-Gate Eye Part No. Select Quantity

This fitting is designed as a gate eye for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.

C31G20
C31G25
C31G32
C31G40
C32-Gate Hinge Part No. Select Quantity

This fitting is designed as a gate hinge for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.

C32G20
C32G25
C32G32
C32G40
C33-Hook Part No. Select Quantity

The fitting is designed to provide an attachment for chain.

C33G20
C33G25
C33G32
C33G40
C34-Fixing Pad Part No. Select Quantity

The fitting is designed to provide an attachment for flat sheets or board. It may also be used as a gate stop. An alternative fitting for the attachment of boards is the C35 type.

C34G25
C34G32
C34G40
C35-Male Swivel Part No. Select Quantity

The Male Swivel can be used on its own for use with a shakle and chain or with the C36 female swivel to mount rails at any angle for slopes. It can also be used for attaching flat sheets or boards to a structure and is available assembled with the C36 fittings as a C45 single swivel combination.

C35G20
C35G25
C35G32
C35G40
C35G50
C36-Female Swivel Part No. Select Quantity

The Female Swivel is designed as part of the swivel combination group of fittings. It can be used with the C10, C35, C37, C38 or C39 male swivel fittings.

C36G20F
C36G25F
C36G32F
C36G40F
C36G50F
C37-Double Swivel Male Part No. Select Quantity

The Double Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings. The double swivel combination is also available assembled as a type C47 fitting.

C37G20
C37G25
C37G32
C37G40
C37G50
C38-Corner Swivel Male Part No. Select Quantity

20nb 90° Corner Swivel Male

The 90° Corner Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings to make a corner combination fitting which is also available assembled as a type C48 type fitting.

C38G20
C38G25
C38G32
C38G40
C39-Socket Swivel Male Part No. Select Quantity

The SocketMale Swivel is designed as part of the swivel combination group of fittings. It can be usedwith aC36 Female Swivel and aC41 Clamp on Tee fitting tomake a swivel combination fitting thatwill provide an angled strut for an existing structurewithout dismantling.

C39G20
C39G25
C39G32
C39G40
C39G50
C40-90° Crossover Part No. Select Quantity

The 90° Crossover connects two rails at 90° to each other and is often used for the handrailing when continuous standard lengths of tube are used. Please note that tube joints should use the C00 or C01 type fitting, and not the C40 type fitting.

C40G20
C40G25
C40G32
C40G40
C40G50
C41-Clamp On Tee Part No. Select Quantity

The Clamp on Tee is designed to allow a new tube to be joined to an existing structure. Torque maximum 15N\M. This uses a M10 stainless steel bolt.

C41G20
C41G25
C41G32
C41G40
C41G50
C42-Clamp On Crossover Part No. Select Quantity

The Clamp on Crossover is designed to allow a new tube to be joined to an existing structure.

C42G20
C42G25
C42G32
C42G40
C42G50
C43-Combination Socket Part No. Select Quantity

The Combination Socket is designed for racking and similar systems to allow a crossover to be combined with a cross tie.

C43G20
C43G25
C43G32
C43G40
C45-Single Swivel Combination Part No. Select Quantity

The Single Swivel Combination is designed to provide and angled tee between two tubes. It can be used to construct sloping handrail and for providing bracing struts to structures.

C45G20
C45G25
C45G32
C45G40
C45G50
C46-Base Swivel Combination Part No. Select Quantity

The Base Swivel Combination is designed to provide an angled wall or floor mounting. This fitting should not be used as a railing base without suitable support.

C46G20
C46G25
C46G32
C46G40
C46G50
C47-Double Swivel Combination Part No. Select Quantity

The Double Swivel Combination is designed to provide an in line angled joint as a post, this is suitable for the mid rail of a sloping handrail or to provide bracing to a structure.

C47G20
C47G25
C47G32
C47G40
C47G50
C48-90° Corner Swivel Combination Part No. Select Quantity

The 90° Corner Swivel Combination is designed to provide an angled joint at a post, this is suitable for the mid rail of sloping handrail or to provide bracing to a structure.

C48G20
C48G25
C48G32
C48G40
C49-Clamp On Swivel Combination Part No. Select Quantity

TheClamp on Swivel Combination is designed to provide an angled tee between two tubes, one ofwhich is part of an existing structure. It can be used for providing bracing struts to structures.

C49G20
C49G25
C49G32
C49G40
C49G50
C50-Slope Elbow ± 11° Part No. Select Quantity
C50G40
C51-Slope Short Tee ± 11° Part No. Select Quantity

The Slope Short Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.

C51G40
C52-Slope Long Tee ± 11° Part No. Select Quantity

The Slope Long Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.

C52G40
C53-Slope Railing Base ± 11° Part No. Select Quantity

The Slope Base is designed to provide a base for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.

C53G40
C54-Slope 2 Socket Cross ± 11° Part No. Select Quantity

The Slope 2 Socket Cross is designed to provide a joint for the midrail for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.

C54G40
C55-27 1/2° Ridge Fitting Part No. Select Quantity

A four way socket fitting used to construct the ridge of a roof structure.

C55G40
C56-27 1/2° Eaves Fitting Part No. Select Quantity

A four way socket fitting used to construct the eaves of a roof structure.

C56G40
C60-Screws to Suit 20 & Fittings Part No. Select Quantity

Spare Screws come in two sizes, 1/4” ISO 228 for the 20 and 25nb range and 3/8” ISO 228 for the 32, 40 and 50 ranges.

C60S25
C60S32/40
C61-6mm Allen Key to Suit 20 & Fittings Part No. Select Quantity

Allen keys are available in two sizes, the first is suitable for the 20 and 25nb fitting and the other for the 32, 40 and 50nb fittings.

C61S25
C61S32/40
C62-C62R Part No. Select Quantity

Ratchet Key

The Ratchet driver and dual keys are available to speed assembly. The Ratchet driver will allow tightening to the correct torque.

C62R
C65-Plastic End Caps Part No. Select Quantity

Plastic End Caps are available for finishing plain end tubes. Available in grey plastic they will fit medium and heavy gauge tube.

C65P20
C65P25
C65P32
C65P40
C65P50
C66-Single Mesh Clip Part No. Select Quantity

The Single Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips are spaced at a maximum of 450mm apart.

C66G20
C66G25
C66G32
C66G40
C66G50
C67-Double Mesh Clip Part No. Select Quantity

The Double Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips are spaced at a maximum of 450mm apart.

C67G20
C67G25
C67G32
C67G40
C67G50
C68-Base Weather Cowl Part No. Select Quantity

The Weather Cowl is designed to cover the Railing base and provides a weather proof seal when used with a suitable flexible sealant.

C68G25
C68G32
C68G40
C69-Square Plastic End Cap Part No. Select Quantity

The Plastic End Caps are available for finishing plain end square tubes. Available in grey plastic they will fit medium and heavy tube gauges.

C69P40
C69P50
C69P70
EC1-EC11 Part No. Select Quantity
 
EC11
EC12G40
EC10050
EC2-EC2525 Part No. Select Quantity
 

End Caps 25 x 25 x 2 - 3mm

EC2525
EC4-EC4040 Part No. Select Quantity
 

End Caps 40 x 40 x 1.5 - 3mm

EC4040
EC404025
EC5-EC5050 Part No. Select Quantity
 

End Caps 50 x 50 x 2.5 - 5mm

EC5050
EC5025
EC8-EC8080 Part No. Select Quantity
 

End Caps 80 x 80 x 2.5 - 4mm

EC8080
C70-Straight Crimp Joint to Suit Handrailing Part No. Select Quantity

Straight Crimp Joints provide a permanent in-line connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary.

C70G25
C71-Crimp Elbow Joint to Suit Handrailing Part No. Select Quantity

Crimp Elbow provides a permanent 90° connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary.

C71G25
C72-Variable Angle Crimp Elbow Joint to Suit Handrailing Part No. Select Quantity

Crimp Variable Elbow’s provide a permanent variable angled connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary and these are available for hire or purchase.

C72G25
CA0-Add On Short Tee Part No. Select Quantity

The Add On short Tee allows existing structures to be added to without the need for any dismantling. Tubes must not be jointed within this fitting.

CA03G32
CA03G40
CA4-Add On 90° Crossover Part No. Select Quantity

The Add On 90° Crossover allows existing structures to be added to without the need for any dismantling. This fitting is designed to give a 90° offset crossover joint. Tubes must not be joined within this fitting.

CA40G32
CA40G40
GBG-Tube Part No. Select Quantity
 
GBGM20
GBGM25
GBGM32
GBGM40
GBGM50
DDA01-Upright Connector Part No. Select Quantity

Connector for attaching the DDA04 intermediate bracket or the DDA02 handrail connector to the 48.3mm o/d upright.

DDA01
DDA02-Handrail Upright Part No. Select Quantity

Connector (made from Ductile Iron) for attaching the end of the 42.4mm o/d handrail tube at 90° to the 48.3mm o/d upright. This bracket is used in conjunction with DDA01 and DDA07.

DDA02
DDA03-Wall Bracket Part No. Select Quantity

Bracket (made from Ductile Iron) for supporting the 42.4mm o/d handrail tube to a wall. The 42.4mm o/d tube is fixed to the DDA03 using either 2 x self tapping screws or 2 x pop rivets.

DDA03
DDA04-Intermediate Bracket Part No. Select Quantity

Bracket (made from Ductile Iron) for supporting the top or middle rail tube at an upright in conjunction with a DDA01. The 42.4mm o/d tube is fixed to the DDA04 using either 2 x self tapping screws or 2 x pop rivets.

DDA04
DDA05-End Return Part No. Select Quantity

Bracket (made from Ductile Iron) for terminating the 42.4mm o/d handrail tube back to a wall. This bracket is used in conjunction with a DDA07.

DDA05
DDA06-90° Bend Part No. Select Quantity

Expanding elbow (made from Ductile Iron) for creating a smooth 90° bend in the 42.4mm o/d tube.

DDA06
DDA07-Internal Connector Part No. Select Quantity

Expanding internal connector for joining sections of 42.4mm o/d tube, or other DDA fittings as and when required.

DDA07
DDA08-Plastic End Cap Part No. Select Quantity

48.3mm o/d plastic end cap for inserting into the open tube on the top of the upright. For a permanent fix, a suitable adhesive should be used.

DDA08
DDA09-Adjustable Bend Part No. Select Quantity

Fitting (made from Ductile Iron) for creating an adjustable bend between the horizontal and the vertical.

DDA09

We'll call you back

Enter your contact details below and we'll call you straight back: